# Configuration Moes ZM-1P100M-M-MS Tuya/Zigbee **URL:** \ **Category:** Configuration\ **Created:** [October 19, 2026, 3:57pm UTC](https://community.gladysassistant.com/t/configuration-moes-zm-1p100m-m-ms-tuya-zigbee/11369 "2026-10-19T15:57:20Z")\ **Posts on this page:** 5\ **Page:** 1
**Author:** ![Olivier.L57](https://gladys-assistant-community.b-cdn.net/letter_avatar_proxy/v4/letter/o/cdc98d/32.png) [@Olivier.L57](https://community.gladysassistant.com/u/Olivier.L57)\ **Post date:** [October 19, 2026, 3:57pm UTC](https://community.gladysassistant.com/t/configuration-moes-zm-1p100m-m-ms-tuya-zigbee/11369/1 "2026-10-19T15:57:20Z")
Dear Geek and Gladys Expert Friends Here’s a bone to chew on that I’ve already chipped a few teeth on, but I’m learning and I have room for improvement I tried an external configuration of a ZM-1P100M-M-MS (TZE28C1000000\_2fnssffc to be exact) in Zigbee I found this source [[New device support]: MOES ZM6LT1 1-Phase Energy Power Meter With Current Transformer Sensor Clamp · Issue #32416 · Koenkk/zigbee2mqtt · GitHub](https://github.com/Koenkk/zigbee2mqtt/issues/32416) I applied the latest version, I have data feedback. I have two devices. One at the output of my BEEM-ON 500w (self-consumption) and the other at the input of my circuit breaker (overall house consumption) My question. Who has already dealt with this device and does the configuration seem relevant? My doubts: Apart from the voltage, I’m not sure about the accuracy of the other information… Thank you 🙂 🙃 ---
**Author:** ![cicoub13](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/cicoub13/32/4482_2.png) [@cicoub13](https://community.gladysassistant.com/u/cicoub13)\ **Post date:** [October 22, 2026, 7:25am UTC](https://community.gladysassistant.com/t/configuration-moes-zm-1p100m-m-ms-tuya-zigbee/11369/2 "2026-10-22T07:25:28Z")
Hi Olivier, Good news: you shouldn’t need an external converter anymore 🙂 Your meter (I assume the exact ID displayed in Zigbee2mqtt is `_TZE284_2fnssffc`) is **natively supported by Zigbee2mqtt since version 2.13.0** , under the name **Moes ZM6LT1**. This is the issue code you found, officially integrated via [this PR](https://github.com/Koenkk/zigbee-herdsman-converters/pull/12618). And since v5.1.4, Gladys includes Zigbee2mqtt 2.14.2. ### What I propose 1. Check the version of Gladys and that of Zigbee2mqtt (Z2M interface \> Settings \> About). 2. Remove the external converter, then restart Zigbee2mqtt. 3. In the device page in Z2M, verify that it appears as « Moes ZM6LT1 », natively supported. 4. In Gladys, restart Zigbee2mqtt discovery and update the device to retrieve the correct features. ### The exposed measurements - `energy`: consumed energy index (in the direction of the clamp) - `reverse_energy`: energy index in the reverse direction (injected) - `voltage`, `current`, `power`, `ac_frequency` On the Gladys side, voltage, current, power, and the `energy` index are taken. `reverse_energy`, `active_energy`, and frequency are not yet reported. ### Common pitfalls that distort measurements - **The clamp must surround a single conductor (the phase), not the entire cable.** If it surrounds the phase and the neutral, the two currents cancel each other out, and you will read a current and power close to 0. This was exactly the problem of the person in the GitHub issue. - **The direction of the clamp** : the arrow must point in the direction of the current you want to measure (from the grid to the house for the general, from the BEEM to the house for production). If it is reversed, the energy accumulates in `reverse_energy` instead of `energy`. - **Power and current have no sign.** On the main meter, if your BEEM produces more than what the house consumes at that moment, you will still see a positive power even though you are injecting. Only the `energy` / `reverse_energy` indices allow you to know the direction of the current. ### To verify if the values are correct - Turn on a known load (e.g., a 2000 W kettle): on the main meter, `power` should increase by approximately 2000 W and `current` by approximately 2000 / 230 ≈ 8.7 A. - Check that `power` ≈ `voltage` × `current` (approximately, the power factor comes into play). - Compare the BEEM meter with the production displayed in the BEEM app, and the index of the main meter with the evolution of your Linky over a day. If something is still wrong after that, can you share: - your versions of Gladys and Zigbee2mqtt, - a screenshot of the « State » tab of each of the two devices in Zigbee2mqtt, - the values you expected at the same time (BEEM app, Linky…) ? We can then precisely see which measurement is incorrect. ---
**Author:** ![Olivier.L57](https://gladys-assistant-community.b-cdn.net/letter_avatar_proxy/v4/letter/o/cdc98d/32.png) [@Olivier.L57](https://community.gladysassistant.com/u/Olivier.L57)\ **Post date:** [October 22, 2026, 11:31am UTC](https://community.gladysassistant.com/t/configuration-moes-zm-1p100m-m-ms-tuya-zigbee/11369/3 "2026-10-22T11:31:06Z")
Hi Cicoub Thanks for your reply, for your long detailed reply! It comes at a good time, as I just received an order for modules to redo the mesh of my house. An old house with thick walls… it’s a bit of a hassle. So I’m going to start from scratch to get a nice clean mesh. Thanks for your involvement. ---
**Author:** ![Olivier.L57](https://gladys-assistant-community.b-cdn.net/letter_avatar_proxy/v4/letter/o/cdc98d/32.png) [@Olivier.L57](https://community.gladysassistant.com/u/Olivier.L57)\ **Post date:** [October 24, 2026, 1:47pm UTC](https://community.gladysassistant.com/t/configuration-moes-zm-1p100m-m-ms-tuya-zigbee/11369/4 "2026-10-24T13:47:33Z")
Hello, I have checked the versions, removed the external conv, restarted the discovery, but no it remains in « \generated support » It’s a \_TZE28C1000000\_2fnssffc ![Screenshot 2026-10-19 000151](https://gladys-assistant-community.b-cdn.net/uploads/default/original/3X/1/d/1dee1db3c39ccdb183601ec7b43e5e52ae4d44a4.jpeg) ---
**Author:** ![cicoub13](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/cicoub13/32/4482_2.png) [@cicoub13](https://community.gladysassistant.com/u/cicoub13)\ **Post date:** [November 4, 2026, 9:06am UTC](https://community.gladysassistant.com/t/configuration-moes-zm-1p100m-m-ms-tuya-zigbee/11369/5 "2026-11-04T09:06:19Z")
Thanks Olivier for your feedback! « Generated support » means that Zigbee2mqtt does not recognize the device ID and manages it generically. So I need to see exactly what it reports. Can you share: 1. **The exact versions** of Gladys and Zigbee2mqtt (Z2M \> Settings \> About). 2. **A screenshot of the « About » tab** of the device in Z2M, with the _Zigbee Model_ and _Zigbee Manufacturer_ fields visible. The best is to copy and paste them here as text. The ID `_TZE28C1000000_2fnssffc` seems odd to me, I want to make sure there is no reading error. 3. **A screenshot taken after your changes** : the one you posted is from 10/19, so before the converter was removed. Did you also restart Zigbee2mqtt after removing the converter? If so, you can try removing the device from Z2M and then re-pairing it. Thanks!