# Zigbee2MQTT refresh **URL:** \ **Category:** Configuration\ **Created:** [January 12, 2023, 10:53pm UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831 "2023-01-12T22:53:01Z")\ **Posts on this page:** 10\ **Page:** 1
**Author:** ![Riquet0077](https://gladys-assistant-community.b-cdn.net/letter_avatar_proxy/v4/letter/r/e95f7d/32.png) [@Riquet0077](https://community.gladysassistant.com/u/Riquet0077)\ **Post date:** [January 12, 2023, 10:53pm UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/1 "2023-01-12T22:53:01Z")
Hello everyone, I use Z2M to retrieve temperature and humidity sensor data from Xiaomi [WSDCGQ11LM](https://www.zigbee2mqtt.io/devices/WSDCGQ11LM.html#xiaomi-wsdcgq11lm). For some time now, 3 of the 4 installed have not been permanently connected: message of no data recorded recently. As soon as I stop Z2M in Galdys and restart it, the data reappears. After a short analysis in Z2M, I think these are sensors that, at least at some point, did not have a direct contact with the gateway but were going through an intermediary. Other info: to use thermostatic valves [ME167](https://www.zigbee2mqtt.io/devices/ME167.html#avatto-me167) not natively recognized in Z2M, I added an additional module. Everything, however, works well in Z2M. Any idea? ---
**Author:** ![lmilcent](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/lmilcent/32/7023_2.png) [@lmilcent](https://community.gladysassistant.com/u/lmilcent)\ **Post date:** [January 13, 2023, 5:44am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/2 "2023-01-13T05:44:57Z")
Hi, Same problem with my Xiaomi Aqara temperature and humidity sensors. I feel like they disconnect from time to time, maybe as you say, when their signal is relayed. On the internet it seemed to be an issue specific ---
**Author:** ![VonOx](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/vonox/32/10128_2.png) [@VonOx](https://community.gladysassistant.com/u/VonOx)\ **Post date:** [January 13, 2023, 6:41am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/3 "2023-01-13T06:41:17Z")
Same here, I reconnected 3 of them 2 days ago. They’re going to end up in the trash; I think I’ll replace them with Sonoff. ---
**Author:** ![guim31](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/guim31/32/4840_2.png) [@guim31](https://community.gladysassistant.com/u/guim31)\ **Post date:** [January 13, 2023, 6:56am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/4 "2023-01-13T06:56:06Z")
I’m also having problems with some of my Aqara temperature sensors… 😕 I just bought a few of them on AliExpress, Tuya model, I’ll give you feedback! 👍 ---
**Author:** ![lmilcent](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/lmilcent/32/7023_2.png) [@lmilcent](https://community.gladysassistant.com/u/lmilcent)\ **Post date:** [January 13, 2023, 9:13am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/5 "2023-01-13T09:13:07Z")
It’s a bit like IKEA devices; they work better if they’re paired with another device from the same brand. Long live the jungle of brands and the various ways of implementing a standard! ---
**Author:** ![spenceur](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/spenceur/32/1961_2.png) [@spenceur](https://community.gladysassistant.com/u/spenceur)\ **Post date:** [January 13, 2023, 9:16am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/6 "2023-01-13T09:16:22Z")
I replaced all my Aqara temperature sensors with Sonoff ones and it works much better and lasts longer! ---
**Author:** ![Tlse-vins](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/tlse-vins/32/6054_2.png) [@Tlse-vins](https://community.gladysassistant.com/u/Tlse-vins)\ **Post date:** [January 13, 2023, 10:18am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/7 "2023-01-13T10:18:27Z")
I only have Sonoff (6), and I don’t have any disconnections. ---
**Author:** ![Riquet0077](https://gladys-assistant-community.b-cdn.net/letter_avatar_proxy/v4/letter/r/e95f7d/32.png) [@Riquet0077](https://community.gladysassistant.com/u/Riquet0077)\ **Post date:** [January 13, 2023, 7:42pm UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/8 "2023-01-13T19:42:20Z")
Thanks everyone for your responses. It’s nice not to feel alone. However, I was hoping for a less radical solution than throwing everything away because apparently, at least for me, the sensors work fine: they communicate with the gateway and the information is available in Z2M. I think it’s rather the connection with Gladys that’s causing the problem, hence my request. As soon as I restart the integration, the information is updated! ---
**Author:** ![spenceur](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/spenceur/32/1961_2.png) [@spenceur](https://community.gladysassistant.com/u/spenceur)\ **Post date:** [January 13, 2023, 9:06pm UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/9 "2023-01-13T21:06:21Z")
Otherwise, the solution is to use the Xiaomi module directly instead of Zigbee if you don’t want to replace them 🙂 ---
**Author:** ![Will\_71](https://gladys-assistant-community.b-cdn.net/user_avatar/community.gladysassistant.com/will_71/32/9582_2.png) [@Will\_71](https://community.gladysassistant.com/u/Will_71)\ **Post date:** [January 14, 2023, 11:54am UTC](https://community.gladysassistant.com/t/rafraichissement-zigbee2mqtt/7831/10 "2023-01-14T11:54:25Z")
As for me, I’ve only had Aqara temperature sensors for 3 years with no problems! You’re scaring me, so I don’t want to change everything — I just hope it lasts!